Home · Blog · Fundamentals

Hertz-Mindlin or Linear Spring-Dashpot: which DEM contact model to use

⚖️ Fundamentals · Aug 18, 2026 · 8 min read

δ overlap Hertz-Mindlin Linear Spring-Dashpot contact model Fn force
What the contact model does: it turns the overlap between two particles into a force. BrixDEM ships two, and choosing between them is what this article is about.
Every DEM solver needs a contact model: the rule that turns the overlap between two particles into a force. BrixDEM ships two, Hertz-Mindlin and Linear Spring-Dashpot. They solve the same thing in different ways. This guide shows the difference, when to use each one, and the detail almost everyone forgets when switching models.
Short answer: use Hertz-Mindlin when the magnitude of the forces matters (wear, wall loads, packing). Use Linear Spring-Dashpot when what matters is the flow, and you want speed in studies, calibration and large models.

What the two have in common

Both build the contact the same way: a spring, which produces the force from the overlap, and a dashpot, which dissipates energy and gives the coefficient of restitution. That holds in the normal and in the tangential direction. The tangential branch also has the friction limit: the force never exceeds μ·Fn, and beyond that it slides.

i j NORMAL spring: stiffness (linear or Hertzian) dashpot: restitution TANGENTIAL friction limit μ·Fₙ
The contact structure, identical in both models: spring and dashpot acting in parallel, in the normal and tangential directions, with the friction limit on the tangential branch. What changes between the models is only the spring.

The difference: how the force grows

The distinction is in the normal spring. In Linear Spring-Dashpot the force is proportional to the overlap, so the stiffness is constant. In Hertz-Mindlin the force grows with the overlap raised to 1.5, which comes from the elastic contact theory between two spheres. In practice, the Hertzian contact is softer on a light touch and stiffens as the load increases.

overlap δ normal force Fₙ Linear Spring-Dashpot Fₙ = kₙ · δ  ·  constant stiffness Hertz-Mindlin Fₙ ∝ δ1.5  ·  stiffens under load
Normal force against overlap. The blue straight line is the linear model, with constant stiffness. The green curve is the Hertzian one, softer at first and stiffer under load.

Hertz-Mindlin

It is the default for most granular materials. The stiffness comes from the material properties (Young's modulus and Poisson's ratio), so the parameters carry direct physical meaning.

  • Advantages: it describes the real contact force better, especially under high load, and the packing under self weight. It is the natural choice when you are going to report forces, stresses or wear.
  • Limitations: it costs more per contact and the stiffness changes with the load, which demands more care with the time step in heavily compressed regions.
  • Use it when: the result that matters is force, wall stress, wear or bed compaction.

Linear Spring-Dashpot

The stiffness is set directly and does not change. It is the simplest and most predictable model.

  • Advantages: faster, with a stable time step that is easy to estimate. Because you control the stiffness directly, it is excellent for parameter sweeps and for calibration loops.
  • Limitations: constant stiffness does not reproduce the stiffening of the real contact, so force peaks under high load are less faithful.
  • Use it when: the result that matters is the flow pattern, the throughput or the process time, and you want to run more cases in less time.

Quick comparison

 Hertz-MindlinLinear Spring-Dashpot
Normal forcenonlinear (δ1.5)linear (kn·δ)
Stiffnessgrows with loadconstant
Main inputmaterial propertiesstiffness set directly
Cost per contacthigherlower
Best forforce, stress, wearflow, calibration, large models

How to choose in practice

Ask what you are going to report. If the answer is a force number (wall load, torque, wear), go with Hertz-Mindlin. If the answer is how the material moves (does it clog or not, how much comes out per hour, how long it takes), the linear model delivers the same behavior at a lower cost.

Worth noting: in dry granular flow, both calibrated models usually give similar flow patterns, because the flow is dominated by friction and geometry, not by the shape of the spring. The difference shows up when the material gets compressed and the magnitude of the force starts to matter.

Careful when switching models: calibration does not carry over from one to the other. Parameters are tuned inside a given contact model, so moving from Hertz-Mindlin to Linear Spring-Dashpot (or the other way around) means you have to recalibrate and review the time step.

Frequently asked questions

Which one should I use if I'm starting out?

Start with Hertz-Mindlin, the default for most granular materials, using parameters with physical meaning. Switch to the linear model if you need more speed in studies and calibration.

Do the two give the same result?

In well-calibrated dry flow, the flow pattern is usually similar. The contact force values are not. If you report force, stress or wear, the choice of model changes the number.

Does the contact model change friction and restitution?

No. Restitution, sliding friction and rolling friction remain parameters of the material pair in both models. What changes is how the normal spring computes the force.

Do I need to recalibrate when switching models?

Yes. Calibrated parameters are valid for the model they were tuned in. Rerun the calibration tests in the new model before trusting the result.

Try both models

BrixDEM ships Hertz-Mindlin and Linear Spring-Dashpot in the same solver. Switch the model and compare on your own case.

Back to blog