Home · Blog

BrixDEM Blog

DEM fundamentals, calibration, applications and best practices — for those who simulate granular flow.

📳
Applications · 7 min

Three-deck vibrating screen: what the simulation shows on each deck

Case study of a 6.0 × 2.4 m three-deck vibrating screen at 12 Hz with 80, 40 and 20 mm openings: screen acceleration, diameters on each deck, rocks smaller than the opening and material speed.

Read article →
🪨
Applications · 6 min

Jaw crusher: what happens inside the crushing chamber

How a jaw crusher works and what happens inside the chamber, rock by rock: how it fills, why crushing comes in jumps, how the force pulses and what changes in material size.

Read article →
💥
Release notes · 6 min

BrixDEM 1.8: particle breakage, liquid bridges and support for newer GPUs

Version 1.8 brings the particle breakage model (AB-t10 + PRM), liquid bridges for wet materials, dynamic contact slots, support for newer GPUs, a perspective/orthographic toggle in 3D, Spanish and Sketch improvements.

Read article →
🚜
Applications · 6 min

Apron feeder: operation and DEM analysis

Learn how an apron feeder works and how DEM simulation helps assess flow, discharge, contact loads and regional wear.

Read article →
⚙️
Applications · 9 min

Bin blender vs octagonal blender: when average power misleads

Two tumble blenders at the same speed and with the same charge, simulated in BrixDEM. Average power is almost identical, but the bin has 67% higher peaks, torque swinging from 13 to 1,577 N·m every turn, and moments when the load drives the vessel.

Read article →
⚡
Release notes · 8 min

BrixDEM 1.7: a clearer interface, a more reliable solver and a faster Mixed GPU

Version 1.7 brings a new motion and geometry interface, stability fixes, safer checkpoints, deterministic contact history and performance improvements in Mixed GPU execution.

Read article →
🚂
Applications · 10 min

Railcar loading: what happens in the ten seconds the gate is open

A DEM case study of a railcar loading station: 190,000 multi-sphere particles, a silo with a clamshell gate, 1.7 MJ of energy released, 17 m/s impact on the wagon floor, and why the load forms a crown instead of filling level.

Read article →
⛏️
Applications · 10 min

Transfer chutes: straight drop or cascade? Two DEM case studies

What a transfer chute has to do and what goes wrong. Two cases simulated in BrixDEM: a straight-drop chute from CAD and a cascade chute with four deflectors, with throughput, dead beds, priming time and a wear map.

Read article →
🧊
Fundamentals · 9 min

Sphere or clump: when the sphere lies (and when it is enough)

Every DEM starts with spheres. See where particle shape changes the answer (angle of repose, silo arching, mixer torque), where a calibrated sphere is enough, what a clump costs, and how to use them in BrixDEM.

Read article →
🥣
Applications · 9 min

More mixing is not always better: the Lacey index in a ribbon mixer

A DEM case study of a ribbon mixer: how the Lacey index and the coefficient of variation measure mixing quality, why homogeneity stopped improving at 5 s, and how to find the optimal mixing time.

Read article →
🚀
Release notes · 9 min

BrixDEM 1.6: multi-sphere particles, Free-body Dynamics and an editable Sketch

Version 1.6 brings multi-sphere particles (clumps) with ready-made types, calibration and wear, free-body dynamics, editing and history in Sketch, CAD import, a cone injector and a faster solver.

Read article →
⚖️
Fundamentals · 8 min

Hertz-Mindlin or Linear Spring-Dashpot: which DEM contact model to use

A practical comparison of the two DEM contact models: how each one computes the force, when to use which, advantages, limitations and why calibration does not carry over from one model to the other.

Read article →
🔄
Applications · 7 min

Rotary valve (airlock feeder): throughput, torque and wear in DEM

A case study from a real CAD: DEM simulation of a rotary valve (rotary feeder / airlock). See pocket filling, dosing throughput, rotor torque and power, and liner wear.

Read article →
🎯
How-to · 11 min

How to calibrate materials in DEM: angle of repose, restitution and friction

A practical, from-scratch guide to DEM material calibration: which parameters to tune, the rebound, inclined-plane and angle-of-repose tests, and how BrixDEM's automatic calibration estimates them for you.

Read article →
⏳
Applications · 9 min

Silo simulation with DEM: filling, discharge and granular flow

How DEM simulates silo and hopper filling and discharge — flow pattern, discharge rate and forces — with a glass-bead case experimentally validated in BrixDEM.

Read article →
🌀
Applications · 10 min

Screw conveyor DEM simulation: how to measure throughput and power

A didactic case study: DEM simulation of a screw conveyor fed by a hopper. Learn how to set the case up and how to read mass flow rate, cumulative mass and mechanical power.

Read article →
🚀
Release notes · 7 min

BrixDEM 1.1: truer contact physics, simpler calibration and new equipment

BrixDEM 1.1 reworks the rolling and twisting resistance models, rebuilds angle-of-repose calibration, and adds continuous mass flow with PSD, coarse-graining and ribbon and paddle mixers in Sketch.

Read article →
🧩
Fundamentals · 9 min

What is the Discrete Element Method (DEM)?

Understand what the Discrete Element Method (DEM) is, how the solver resolves granular flow particle by particle, the contact models, industrial applications and how to start simulating.

Read article →

Want to try it hands-on?

Download BrixDEM for free and run your first DEM simulation today.