What is the Discrete Element Method?
Bulk solids such as sand, cement, grains, ore, tablets and fertilizers behave neither like liquids nor like rigid solids. They form piles, arch over openings, clog and segregate by size and density. Describing that behavior with empirical formulas alone is usually imprecise. DEM solves the problem differently: it represents the material as what it truly is, a collection of discrete particles, and numerically integrates the equations of motion of each one.
The idea was proposed by Cundall and Strack in 1979. As computing power advanced, especially GPUs, it became a standard engineering tool in mining, cement, steelmaking, agribusiness, food and pharmaceuticals.
How DEM works, step by step
The DEM solver repeats a simple loop over very small time steps:
1. Contact detection
At each step, the solver identifies which particles are touching and which touch the equipment walls. Because the number of possible pairs is enormous, neighbor-search algorithms make this efficient.
2. Contact force calculation
Where contact occurs, the solver computes the force from the overlap (δ) between surfaces. This force has a normal component (Fn, repulsion) and a tangential one (Ft, friction), as shown in the diagram below.
The most common contact models are:
- Hertz-Mindlin: nonlinear contact based on elastic contact theory, the standard for most granular materials.
- Linear Spring-Dashpot (LSD): linear stiffness, simpler and faster, ideal for studies and calibration.
Beyond stiffness, behavior is governed by material parameters: coefficient of restitution (how much a collision bounces), sliding friction, rolling friction and, when the material is wet or fine, cohesion.
3. Time integration
Summing all contact forces plus gravity, the solver applies Newton's second law to update each particle's velocity and position. Repeating this loop millions of times, the collective motion of the material emerges exactly as in reality.
What DEM computes (the results)
Unlike empirical correlations, DEM delivers the full physical field:
- Throughput and flow pattern: mass flow versus funnel flow, dead zones and arching.
- Forces and stresses on walls: loads on silos, chutes and liners.
- Segregation: separation by size and density in mixers and transfers.
- Wear: abrasion and impact maps on the geometry, with models such as Archard and Oka.
- Mixing time, homogeneity and energy consumption.
Where DEM is used across industries
Anywhere bulk solids flow, mix, fall or are conveyed. The most common cases include silos and hoppers, mixers, rotary drums and mills, transfer chutes, bucket elevators and bucket-wheel reclaimers. In all of them, DEM simulation anticipates flow, wear and segregation problems without physical prototypes.
Calibration and validation: where trust lives
A DEM result is only trustworthy if the material parameters reproduce real behavior. That is why calibration is essential. Tests such as the rebound test (restitution), the inclined plane (friction between particle and wall) and the angle of repose (friction between particles) tune the parameters to your specific powder or ore. Then reference cases with a known solution validate the solver.
Advantages of simulating with DEM
- Reduces physical prototypes and bench testing.
- Reveals what happens inside the equipment, something impossible to observe directly.
- Lets you test geometries and operating conditions quickly.
- Anticipates clogging, wear and segregation while still in design.
How to start simulating with DEM
BrixDEM is a discrete element simulation software for Windows, with a built-in geometry modeler (Sketch), Hertz-Mindlin and Linear Spring-Dashpot contact models, automatic material calibration and GPU acceleration. You can download it for free and follow the video tutorials to build your first simulation in minutes.
Frequently asked questions about DEM
What does DEM stand for?
DEM stands for Discrete Element Method, a simulation technique that models granular materials particle by particle.
What is DEM used for?
To design and optimize equipment that handles bulk solids, such as silos, mixers, drums, chutes, elevators and conveyors, predicting flow, wear and segregation before manufacturing.
Do I need a GPU to run DEM?
No. The solver runs on a multicore CPU and handles most validation and calibration cases. The GPU (CUDA) accelerates very large models with millions of particles.
Is DEM accurate?
Yes, as long as materials are calibrated and the model validated. DEM solves contact physics from first principles. Accuracy depends on the quality of the input parameters and the user's interpretation.
Put DEM into practice
BrixDEM is free to download and runs on Windows. Simulate your first silo, mixer or drum today.