Home · DEM Course · Module 1
DEM (Discrete Element Method) Course with BrixDEM

Module 1 · Introduction

🎬 7 lessons ⏱ 2 h course 📝 5 questions · pass with 4
🔒

This module is still locked

To unlock it, pass the quiz with at least 70%.

Lesson 5 of 7 · 1:21

Materials, domain and injectors

Lesson transcript

Every DEM case has to answer three questions. What the material is made of. Where the simulation lives. And how material enters and leaves. Let's see all three in the program. Starting with the materials. This case has two: Wall, which is the wall, and Vidro, which is the particles. Each material holds what belongs to it: radius, density and stiffness. That's all. Now the domain. With one click on Fit to Geometry, the box fits around the parts. As simple as that. And insertion. In the inlet I set the velocity and how many particles come in per second. I click Add, and it shows up here in the list. This case already has an inlet, where Vidro comes in, and an outlet, where it leaves. One idea to remember. The material describes the body: density, stiffness, size. The interaction describes two bodies meeting: friction, restitution. Ore on ore is one pair. Ore on steel is another, and they behave differently. That is why what you calibrate is the pair. Before running, watch out for two very common mistakes. Setting up the inlet and forgetting to click Add: without it, the inlet never enters the list. And leaving the normal reversed: the inlet exists, but injects nothing.

Quiz · Module 1

Check what you learned

5 multiple-choice questions. Get at least 4 right to complete the module. You can try as many times as you like.

✓ You have already passed this module. You may retake the quiz to review.
1.What is the core idea of DEM?
2.In what order does the computer repeat the DEM cycle?
3.A restitution of zero means the particle:
4.The simulation diverged: particles fly off and energy rises for no reason. What is the first fix?
5.With coarse-graining at factor three, how many real particles does each simulated particle represent?
Transcripts of every lesson in this module

1. Welcome to the course

In this course you will learn to simulate granular materials: ore, sand, grains, powders. You don't need to know everything beforehand. We go from simple to hard. And everything we explain, you will see working in BrixDEM. By the end, you will be able to build a case, trust the result, and use it in a real engineering decision. There are only a few steps. First, understand what the method is. Then, how particles touch each other. Then you build a real case. You learn to calibrate, so you can trust the numbers. And finally, you run it and read the result. Let's start.

2. What is DEM

Look at this ore chute. Each rock falls, hits its neighbor, pushes the next one. Predicting that with a single formula is very hard. That is where DEM comes in, the Discrete Element Method. The idea is simple: instead of one formula for the whole material, we follow each particle, one by one. Compare it with other simulations, like structural or fluid analysis. They treat the material as one continuous thing, divided into a mesh. That works very well for steel and for water. But a heap of rocks is not continuous: it has voids, collisions, grains bouncing around. So in DEM, each grain is a separate body. And the behavior of the whole material comes from all those contacts together. How does it work? The computer repeats four steps. One: find which particles are touching. Two: compute the force at each contact. Three: apply Newton's law, force gives acceleration. Four: take a small step in time, and every particle moves. Then repeat. Millions of times. In practice, that's all. The rest of the course is detail on these four steps. And why simulate? Because testing large equipment is expensive and slow. With simulation, you spend less on prototypes. You find blockages and wear before you build. You compare options with numbers, not opinions. And you see what happens inside the silo or the mill, where no camera can go. DEM is great for some questions. How long does the silo take to empty? Where will the part wear? Is the material mixing well? How big should the motor be? Now, the catch. If you don't calibrate the parameters, the result shows the trend, but the number itself is not reliable. And the cost grows with the number of particles. That is why the course has a whole module on calibration, and another on how to cut computing time.

3. Getting to know BrixDEM

This is the BrixDEM window, with a silo open. The idea is simple: you set up, run and analyze everything here, without switching programs. Navigation is on the left. And notice: the list is already your workflow, step by step, from top to bottom. First, the geometry: the parts of the equipment. Here we have the silo hopper and a block just below the outlet. Then, the domain. It is this red box: a particle that leaves it no longer exists in the simulation. Third, the materials. Density, stiffness and, further down, how each pair of materials behaves when one touches the other. Fourth, insertion. This is where you say where particles come in, how many, and where they leave. Fifth, the setup: how long to simulate, the time step, gravity, and whether it runs on the CPU or the GPU. And last, the results: you pick the variable and the chart appears. With everything ready, it is down here: Run to run, Pause to pause and Stop to stop. The tabs are in the center: the three-dimensional view, the particles and the charts. And at the bottom, the console, which reports everything the program is doing. Read the console: it usually warns you before a problem becomes an error. Now look at the kind of result you get. This is a ball mill. The drum turns, the lifters raise the balls, and they fall in a cascade. And this is a transfer chute. Every dot you see is a particle, computed with the same four-step cycle.

4. How particles touch

Almost every DEM model starts with spheres. Checking whether two spheres touch is easy: compare the distance between centers with the sum of the radii. The contact physics of spheres is very well known. And because the math is cheap, you can simulate millions of them. A real grain is not a sphere, and we will come back to that shortly. Watch two particles getting close. In DEM, they don't actually break or deform. We let one sphere sink slightly into the other. That small overlap stands for the deformation at the contact point. And it works like a spring: the more they press, the harder they push. All the force comes from that overlap. You can picture it like this. Between the two spheres there is a spring, which pushes. A damper, which removes energy, and that is why the ball does not keep bouncing forever. And sideways, friction, which holds as long as it can. If the sideways force passes the limit, the contact slides. In practice, two ideas come up all the time. Restitution says how much the particle bounces back. One is a perfect ball. Zero, it lands and does not come back up. Friction says how much it holds before it slides. It is what keeps a pile standing. Now the problem with spheres: they roll too much. A pile of marbles does not stand, it spreads out. A real grain has corners, and it locks. To compensate, DEM adds rolling resistance, like a brake at each contact. And when shape really matters, we use clumps, which you will see in a moment. One last point, and a very important one: the size of the time step. If it is small, all goes well. If it is too large, a particle sinks deep into another before the program notices, gets a huge force, and flies off. The simulation gains energy from nothing and blows up. The good news: BrixDEM computes that step for you, from the material and the particle size. Watch for one sign: energy rising for no reason. And if the simulation diverges, the first remedy is to cut the step in half.

5. Materials, domain and injectors

Every DEM case has to answer three questions. What the material is made of. Where the simulation lives. And how material enters and leaves. Let's see all three in the program. Starting with the materials. This case has two: Wall, which is the wall, and Vidro, which is the particles. Each material holds what belongs to it: radius, density and stiffness. That's all. Now the domain. With one click on Fit to Geometry, the box fits around the parts. As simple as that. And insertion. In the inlet I set the velocity and how many particles come in per second. I click Add, and it shows up here in the list. This case already has an inlet, where Vidro comes in, and an outlet, where it leaves. One idea to remember. The material describes the body: density, stiffness, size. The interaction describes two bodies meeting: friction, restitution. Ore on ore is one pair. Ore on steel is another, and they behave differently. That is why what you calibrate is the pair. Before running, watch out for two very common mistakes. Setting up the inlet and forgetting to click Add: without it, the inlet never enters the list. And leaving the normal reversed: the inlet exists, but injects nothing.

6. Shape, scale, calibration, cohesion and wear

The three basic blocks solve a lot. But sometimes the problem asks for more. When grain shape matters. When there are too many particles. When you need numbers you can trust. When the powder sticks. And when the part wears. Let's see the idea behind each one. First, shape. A clump is a group of spheres glued into one rigid body. With it you build long, flat or irregular grains. And see how they interlock, something plain spheres cannot do. Second, scale. Sometimes the equipment holds billions of grains, and no computer can handle that. The way out is coarse-graining: one larger particle stands for several smaller ones, keeping the overall behavior. With a factor of three, one particle counts for twenty-seven, and the run gets much faster. The price is losing the fine detail of the grain. Third, calibration. Contact parameters do not come ready-made. You run a simple test, repeat that test in the simulation, and adjust until the two match. BrixDEM has wizards that do this work, in the Calibration menu. Fourth, cohesion. Moisture forms small liquid bridges between grains. And a very fine powder sticks on its own. You have seen the result in practice: the material flows less, forms arches and blocks. BrixDEM has models for both cases, and it also handles particle breakage. All of that is in Module 4. Finally, wear. BrixDEM accumulates on the part's surface the effect of every grain that slides and every grain that hits. The result is a map like this one: you can see where it will wear first, and compare two designs before building.

7. Three real cases

To close the module, three real cases. The first is a silo. The question is simple: how long does it take to empty? The simulation gave twenty-nine point six five seconds, and the measurement, twenty-nine point two seven. The difference is just over one percent. The lesson: compare against a measured number before you trust the model. The second is a ribbon mixer. Here the question is: is it mixing well, and with how much power? BrixDEM measures mixing quality and shaft power over time. The lesson: turn what you see into numbers, and compare designs on the same chart. The third is a feeder loaded by an excavator. It brings everything together: irregular rock made of clumps, real geometry with moving parts, and a wear map on the bucket. The lesson: when the problem is real, the blocks work together. Before any simulation, ask three questions. Is the project saved? Are all material pairs configured? Are the inlet and outlet in the list? If so, you can run.